Der Aufbau des Champion-Tisches, Teil 2: Rand

Champion Table Build Part219

surface preparation with a Stanley #80 scraper

Champion Table Build Part218

the swirly walnut grain is difficult to plane but the scraper is able to deal with it efficiently

Champion Table Build Part201

beginning to fit the side rails and bread-board ends

Champion Table Build Part203

marking the end cuts with a sharp knife

Champion Table Build Part202

then creating a shoulder along that line with a chisel assures a clean cut without tearing the grain

Champion Table Build Part204

cutting along the shoulder with a sharp crosscut saw

Champion Table Build Part206

a small array of saws to do this job

Champion Table Build Part205

cutting the central breadboard tenon

Champion Table Build Part207

coming up to the other side with a pull-saw

Champion Table Build Part208

both ends of the table are now cut

Champion Table Build Part209

cutting the base of the tenon “cheeks”

Champion Table Build Part210

really no other position to accurately make this cut

Champion Table Build Part211

cutting away the “cheeks”

Champion Table Build Part212

the finished tenon, and a groove has been cut to receive a floating tongue to align the breadboard

Champion Table Build Part213

laying out the positions of the mortise and tenons on the side rails and breadboards

Champion Table Build Part214

cutting the tenon on the side rails

Champion Table Build Part216

checking for a tight fit. the side rails are attached with glued tongue and groove joints, while the breadboards are “floating”, held in place by a tongue and groove joint and two “draw-bored” mortise and tenon joints, which will allow for expansion and contraction where the grain intersects perpendicular rather than parallel, yet holding the boards tight to the edge of the table. Two opposing corners are pinned miters and the other two are mortised.  imagine the table being able to expand in width along the length of the two boards left long to see the allowance for seasonal cross grain movement.

Champion Table Build Part220

treating the edges before the final assembly

Champion Table Build Part217

drilling for the dowels for the pinned miter joints where the live edges come together

Champion Table Build Part221

a brad point drill marks the center of the tenon inside

Champion Table Build Part222

re-marking the tenon with an offset so that the dowel pin will “draw” it tight to the edge of the table.  the holes will be elongated laterally to allow for joint movement.

Champion Table Build Part223

altering geometry with violence

Champion Table Build Part224

shaping the dowel pins by pounding the straight oak through a succession of smaller holes drilled in a steel plate until they are round and the size I need

Champion Table Build Part225

nearly there

Champion Table Build Part227

a batch of pins

Champion Table Build Part226

planing a taper

Champion Table Build Part228

the taper will allow the pin to engage the offset hole in the tenon and slowly pull it tight

Champion Table Build Part230

pounding the pins home for the final assembly

Champion Table Build Part229

a little help form a ratchet strap to pull the center tight

Champion Table Build Part232

cutting away the exposed ends with a saw

Champion Table Build Part233

a tightly pinned joint

Champion Table Build Part234

the top all joined. there will be a considerable amount of detail work on the top yet, but first the base

 

The Eternal Present

eternal present07

Summer waxing

eternal present26

into eternal presence

eternal present12

ancient thunder quivers along the crust

eternal present04

twinning amongst and toppling titans

eternal present14

the smallest witnesses quiet as their gaze

eternal present24

oldest of fault lines wrought with terror for men

eternal present35

Ragnarok not yet come to cleave a line between

eternal present13

the fruits of Eden and the curse

eternal present23

brothers old as Abel and Cain

eternal present01

approach the day with a steady gate

eternal present33

mend the tack and the linkage

eternal present30

the work the day is ready to hand

eternal present19

unfold unfold great sheets unfold

eternal present27

the heavens rain diamonds from the mouth of God

eternal present22

the rye bends, the wheat and barley bend, the corn the teff bend low, below

eternal present20

rust and blood speak and spin

eternal present16

the day is new again

eternal present17

tension speaks in unheard frequencies

eternal present06

felt, like order drawn from skeins of chaos

eternal present25

a fragment of destiny

eternal present11

order from a mystic mind

eternal present10

elder memories

eternal present32

ancient fodder, best fodder

eternal present03

tools for the telling of

eternal present21

tools for the remembering of

eternal present31

the days when Noah stored up faith

eternal present09

quieted his family with peace

eternal present05

as the rim of the earth spilled over

eternal present28

rolling stones 

eternal present29

adjoining man with the presence

eternal present36

again, Noah enters day

eternal present34

moored, listening

eternal present18

breathing presence in

eternal present02

wrested in grace

eternal present15

see how the earth remembers differently

eternal present08

manifest ancient eternal presence

Weitergehen “Go On”

winter’s lathe work

Red oak bowl with salting and beaver teeth-marks.

Red oak bowl with salting and beaver teeth-marks.

box wood

box wood

Many of these bowls are or will be for sale at our Etsy Store: BaumWerk.

Go On, Bezalel

Go On, Bezalel6

“See, I have chosen Bezalel son of Uri, the son of Hur, of the tribe of Judah, 3 and I have filled him with the Spirit of God, with wisdom, with understanding, with knowledge and with all kinds of skills…” Exodus 31: 2 & 3.

Go On, Bezalel3Bezalel is kind of an early renaissance man, thousands of years before Brunelleschi, Michelangelo, or Durer.  More importantly he was faithful to God’s design of him as a craftsman.  He was  found worthy to build the design of God concerning the tabernacle and all of its parts.  As a craftsman and artist, it is hard to comprehend anything so significant to my earthly labors as to manifest on earth something that was authored in the very heart and mind of God.  Go On, Bezalel5

Go On, Bezalel7

Elizabeth Duffy asked me about influences and progenitors in her interview with me last year.  Here is an excerpt of my response pertaining to Bezalel:  I hope, maybe, to be in the line of Bezalel, who fashioned so much for the tabernacle, making the sacred things that were part of the “technology” of worship of His God for his community. Personally, I couldn’t ask for more than that. Bezalel is valuable as a paradigm of an artisan of broad experience and skill. He could work in many trades and arts with skill worthy of God’s Tabernacle. My good friend reminds me of the value of a man of that breadth of experience and skill in contrast to a culture that places a premium on experts of high degree in a single field. When I wonder if I am hurting myself by embracing so many disciplines, I am grateful for Bezalel and his place in God’s story, and a few other men I have encountered who are champions of excellence in this way.Go On, Bezalel1 The drawing, an imagining of a portion of Bezalel’s tent-workshop, started two or three years ago, finally over the past two months I was able to finish it.  It is composed along the lines of another drawing, Go On, Adam, Breathe.  An potential series of drawings?  The drawing to me feels so limited, compared to the vastness of what could be explored and depicted, as a task to learn about Bezalel, his labors, and his relationship to his God.

Go On, Bezalel4

From the Dust I Came

CRY THE BLOOD

I began as dust, heavy with the sweat of God’s fingers as He formed my flesh;  a heap of particles still ringing from the sound of His voice.  His breathe came as a holy wind, compelling me to breath, myself.

“i am erth.”

In my senior year of high school, the man who had been my art teacher since fourth grade, gave me some advice.  I was struggling with the conflicting dreams of pursuing the hope of becoming a musician or studying to become a visual artist.  His counsel was simple and wise:  “you can’t do both.”  At that point of decision, it seemed that since I was largely a self taught musician, I could conceivably continue to be so.  Instinctively I knew that there was so much that I needed to be taught and learn and so much time I needed to devote to the disciplines of drawing and painting.  So, I chose art without regret.  The music, however, has never left.  I have outgrown (mostly) the delusions about being a famous musician.  It has become an intensely personal discipline.  It is a language through which I speak to my God and through which He speaks to me.  It is a language I bless my children with.  It is a language I use to share my heart with those that are close to me.   Times have changed and technology that did not exist or was just emerging when I was young has made it possible for me to share what I have largely kept to myself, my family and my close friends.  It was not an easy decision to share publicly what has been so private.  But this, I have done.

The name of the album is Cry The Blood.  The blood is Jesus’ and the cry is mine, though there are many quiet voices beside me.  I chose to recorded under the pseudonym, i am erth.  (The “a” is missing on purpose, a decision which spell check is relentless in punishing me for.)  The land is a passion of mine and a place of meeting and learning as I live as a son under God’s sky.  I am close to the erth, and it is never far from me.

For the curious:  I wrote the songs, sang all the parts and plucked every string, blew every note, squeezed every box, recorded, mixed and stabbed out every digital pulse.  It is far from perfect.  I blame myself for the flaws, you can decide if there is beauty in them. You can hear my kids, and my animals, the wind and the rain, creaks and clicks and bonks, and probably a freight train.  I’ll thank my friends who encourage me and hold me up in the testing. There is one among those who deserves more credit than any, but I know he prefers anonymity. If you want to thank him, eat a steak or go fly fishing in Montana.

Through the ideas and labor of many, this album will (if not already) ultimately be available for downloaded from major online music retailers. Below is a link to iTunes, where it is already available.

You may be interested in what Elizabeth Duffy has on her blog. Elizabeth is my friend, but she began as a stranger asking me questions.  She has been instrumental in pushing me to make the music available and has written a very encouraging review of as well.  In addition, Elizabeth has included a portion of her interview with me as a means of introduction.  It has been a rare opportunity for me to express what I believe and why I do what I do.  I couldn’t have voiced it without her asking and without the creative, sensitive and trustworthy nature of who she is.  Thank you, Elizabeth.

In a final bit of disclosure, I began an instagram feed early last fall.  While I still remain ambivalent towards much of the usage, I have come to value it as unique for sharing imagery and stories on a different platform and immediacy, it is kind of a microcosm of the posts I make here.  My user name is @baumwerkj if you are interested.

I continually thank you for your support here over the years. It has been 8 years since I began this blog. Your quiet interest has given me encouragement to continue working. All glory and honor will be and ever remain His.

Jack Baumgartner,  Rose Hill, Kansas Jan-19-2015

Sangcræft

guitar1

Sangcræft is old english for the art of “singing” music, including on a musical instrument.  I am using it here to announce a permanent page for music at this website.  You can find it labeled “music” under the work heading on the menu at the top of the page, or use this link.

My Name Is Ash guitar and voice. guitar2

Place

“Rootrill” I hope that you will forgive me for posting an eleven minute song in the twenty first century.  Mostly, I hope that you enjoy it.

Place13

arc contain glow

Place27

seen through scene

Place05

bois d arc meteorite

Place18

slanting even evening light

Place09

ancient bone star dust

Place03

deere ghost sheep goat add straw and mix well

Place24

cross turn

Place08

years unfurl in the eternal present

Place26

young hands dextrous

Place06

core sample of stored solar energy

Place07

made vacant for gold

Place01

quince roots herbs leg

Place23

reamed tapered tapped turned twisted sunk fitted formed around

Place10

concentrate earth line essence

Place16

absorb the sun and use it for life

Place15

pull transfer motion

Place21

dividing even unto cambium and xylem

Place30

layers and layers

Place25

learn purpose practicing discipline

Place14

stop motion

Place12

frozen movement osage root as it once reached

Place31

three forms of light

Place28

hand in hand you who once swayed

Place20

ancient releasing story

Place19

the turning of light upon the solar bank countless voices scratch and turn

Place22

golden hands once full wait for wisdom

Place29

new moon forest window

Place17

tall down cut stack turn stack down

Place04

erth-maker here we bend here we grow

Place11

establish converge into order dust scratcher

Place02

welcome the new bird and fare thee well

Repeats for Commerce

Obed Edom, in the form of a 12″ x 18″ linocut, is for sale on our Etsy Store finally.  Right now, I have 5 impressions available.  Also posted there, are a few bowls which I believe are worthy of consideration.  Thanks everyone for your support, encouragement and attention.  If you missed last week’s post, please give it a look.  I thought it was a good one, but it sort of went under the radar- or perhaps it wasn’t as nice as I fancied.

Obed Edom Print1

Obed Edom, Linocut 12″ x 18″

wormy persimmon bowl

wormy persimmon bowl

wormy persimmon bowl

wormy persimmon bowl

spring bowls 201402

Black walnut salad bowl